GRAIN-SPREADERS

HOME

ABOUT US

PRODUCTS

DEALERS

SA-93

Spread-All Special

*For 6" & 8" Auger

*Without Reversing Switch

*Capacity: Up to 3000 Bu./Hr

(Depending on grain and moisture)

*Powered: Oil Bath Gear Case

*Motor: 1/2 HP 115 V

*Weight: 85 lbs

*Bin Diameters 18 ft to 30 ft

*Vary The Spread by Tilting Pan

SA-94

E-2 Compact

*For 6" & 8" Auger

*With Reversing Switch

*Capacity: Up to 3000 Bu./ Hr

(Depending on grain and moisture)

*Powered: Oil Bath Gear Case

*Motor: 1/2 HP 115 V

*Weight: 85 lbs

*Bin Diameters 18 ft to 36 ft

*Reversible Switch to change from Narrow to Wide Spread

SA-95

E-2 High Speed

*For 6" & 8" Auger

*With Reversing Switch

*Capacity: Up to 3000 Bu./Hr

(Depending on grain and moisture)

*Powered: Oil Bath Gear Case

*Motor: 1/2 HP 115 V

*Weight: 85 lbs

*Bin Diameters 37 ft to 48 ft

*Reversible Switch to change from Narrow to Wide Spread

SA-96

E-3 COMPACT

*For 10" auger

*Without Reversing Switch

*Capacity: 3000 to 4000 Bu./Hr.

(Depending on grain and moisture)

*Powered: oil bath gear case

*Motor: 1/2 HP 115V

*Weight: 85 lbs

*Bin diameters: 18' to 36'

*Vary the spread by tilting pan

SA-97HS

E-3 High Speed

*For 10" Auger

*With Reversing Switch

*Capacity: 3000 to 4000 Bu./Hr

(Depending on grain and moisture)

*Powered: Oil Bath Gear Case

*Motor:1 HP 115 V

*Weight: 100 lbs

*Bin Diameters: 37 t to 48 ft

*Reversible Switch to change from Narrow to Wide Spread

SA-103

E-6

*For 12" Auger

*With Reversing Switch

*Capcaity: 4000 to 6000 Bu./Hr

(Depending on the grain and moisture)

*Powered: Oil Bath Gear Case

*Motor: 1HP 115 V

*Weight:100 lbs

*Bin Diameters 18 ft to 36 ft

*Reversible Switch to change from Narrow to Wide Spread

SA-104HS

E-6 High Speed

*For 12" Auger

*With Reversing Switch

*Capacity: 4000 to 6000 Bu./Hr

(Depending on grain and moisture)

*Powered: Oil Bath Gear Case

*Motor:1 HP 115 V

*Weight: 100 lbs

*Bin Diameters: 37 ft to 48 ft

*Reversible Switch to change Spreading Patterns

SA-105

Spinning Gravity Spreader

*Gravity Spreader designed to help keep fines out of center of smaller bins

*Grain goes through cone and hits inverted cone suspended by shaft that rotates when grain hits bottom cone.

*Has strong hanger straps

(and a leveling strap). Spreader should be level in bin.

* Handles 4000 bushels per hour.

*Lightweight (32#) and comes assembled

SA-98

Galvanized Gravity Spreader

*To help keep fines from center of small bins

*Handles 3000 bushels per hour.

*22 gauge galvanized sheet metal

*Light Weight 15#

(comes unassembled in box)

Note: 3 phase also available, Please specify voltage 230 V. or 460 V.

Note: We recommend a Reversible Spreader on bins Over 30".

SPREAD-ALL MFG

CAUTION: DO NOT STORE SPREADER UPSIDE DOWN, WITH OIL IN OR WARRANTY WILL BE VOID. THE USE OF GROUND FAULT CIRCUIT INTERRUPTERS (GGCI) IS SUGGESTED ON ALL OUTSIDE ELECTRICAL WIRING TO REDUCE POTENTIAL FOR ELECTRICAL SHOCKS.

LUBRICATION - Check the oil level in the gearcase once every 20 hours operating time. The gearcase has an oil fill plug on the top and an oil CHECK PLUG on the side. Maintain an oil level up to the CHECK PLUG in the gearcase. DO NOT OVERFILL THE GEARCASE WITH OIL! Use # 30 SAE Motor Oil in the gearcase.

BEFORE OPERATING SPREADER FILL PROPERLY WITH OIL

1. USE THE BOTTLE OF OIL THAT IS INCLUDED

2. TO PUT OIL IN GEARCASE, REMOVE FILL PLUG ON TOP OF GEARCASE, AND OIL PLUG ON SIDE OF GEARCASE. POUR OIL IN GEARCASE

3. REPLACE FILL PLUG AND OIL LEVEL PLUG IN GEARCASE

CLICK ON THE LINK BELOW FOR WIRING DIAGRAMS & PART LIST

Model E-2, E-3 & E-6 Grain Spreader

Model E-2, E-3 & E-6 Spreaders

Grain Spreader Part List

Instructions

Model E-2 , E-3 & E-6 GRAIN SPREADERS

Assembly Instructions

1. Remove all parts from the carton.

2. Bolt the 3 hanger straps to the hopper,2 bolts each, hooks out, either, lenghten or shorten them to accommodate different bin opening sizes.

3. Turn the unit upside down & gently slide the sleeved end of the impeller shafts assembly onto the protruding end of the output shaft. Be sure that the sleeved shaft is way down against the bearing on the output shaft. Then tighten the 5/16-18x 5/8 set screw.

IMPORTANT: BE SURE THE SET SCREW IS TIGHTENED PROPERLY.

4. Pivot the spreading impeller to a sharp angle. DO NOT loosen the pivot locking nut. A spring washer retains adequate tension to hold the impeller in a selected position. When the unit is new, extra pressure maybe required to make the impeller pivot to different angles.

5. Bolt all three spreading vanes so that the long tapered end is outward on the impeller.

Note: The short side of the impeller holds the spreader vane at a much sharper angle.

6. Add 1 quart oil (included)

7. The unit is now ready to install in your bin

Installation And Operation

1. Hang the unit into the bin. CENTER IT and LEVEL IT with a carpenter's level.

2. Connect the power cord to the 110 Volts A. C. Grounded Supply

3. The unit is ready to operate.

4. Changing the angle of the impeller up and down to different positions will adjust the spreading pattern. Never leave the angle in one setting for a long period of time. Tilting the long end of the impeller downward sharply usually is the best for the lower fill in the bin. Gradually flattening the angle as the bin fills is the best procedure. So changing back and forth often works well in larger diameter bins.